LEE- Uçak ve Uzay Mühendisliği Lisansüstü Programı
Bu topluluk için Kalıcı Uri
Yazar "511171148" ile LEE- Uçak ve Uzay Mühendisliği Lisansüstü Programı'a göz atma
Sayfa başına sonuç
ÖgeA study on static and dynamic buckling analysis of thin walled composite cylindrical shells(Graduate School, 2022-01-24) Özgen, Cansu ; Doğan, Vedat Ziya ; 511171148 ; Aeronautics and Astronautics Engineering ; Uçak ve Uzay MühendisliğiThin-walled structures have many useage in many industries. Examples of these fields include: aircraft, spacecraft and rockets can be given. The reason for the use of thin-walled structures is that they have a high strength weight ratio. In order to define a cylinder as thin-walled, the ratio of radius to thickness must be more than 20, and one of the problems encountered in the use of such structures is the problem of buckling. It is possible to define the buckling as a state of instability in the structure under compressive loads. This state of instability can be seen in the load displacement graph as the curve follows two different paths. The possible behaviors; snap through or bifurcation behavior. Compressive loading that cause buckling; there may be an axial load, torsional load, bending load, external pressure. In addition to these loads, buckling may occur due to temperature change. Within the scope of this thesis, the buckling behavior of thin-walled cylinders under axial compression was examined. The cylinder under the axial load indicates some displacement. When the amount of load applied reaches critical level, the structure moves from one state of equilibrium to another. After some point, the structure shows high displacement behavior and loses stiffness. The amount of load that the structure will carry decreases considerably, but the structure continues to carry loads. The behavior of the structure after this point is called post-buckling behavior. The critical load level for the structure can be determined by using finite elements method. Linear eigenvalue analysis can be performed to determine the static buckling load. However, it should be noted here that eigenvalue-eigenvector analysis can only be used to make an approximate estimate of the buckling load and input the resulting buckling shape into nonlinear analyses as a form of imperfection. In addition, it can be preferred to change parameters and compare them, since they are cheaper than other types of analysis. Since the buckling load is highly affected by the imperfection, nonlinear methods with geometric imperfection should be used to estimate a more precise buckling load. It is not possible to identify geometric imperfection in linear eigenvalue analysis. Therefore, a different type of analysis should be selected in order to add imperfection. For example, an analysis model which includes imperfection can be established with the Riks method as a nonlinear static analysis type. Unlike the Newton-Rapson method, the Riks method is capable of backtracking in curves. Thus, it is suitable for use in buckling analysis. In Riks analysis, it is recommended to add imperfection in contrast to linear eigenvalue analysis. Because if the imperfection is added, the problem will be bifurcation problem instead of limit load problem and sharp turns in the graph can cause divergence in analysis. Another nonlinear method of static phenomena is called quasi-static analysis which is used dynamic solver. The important thing to note here is that the inertial effects should be too small to be neglected in the analysis. For this purpose, kinetic energy and internal energy should be compared at the end of the analysis and kinetic energy should be ensured to be negligible levels besides internal energy. Also, if the event is solved in the actual time length, this analysis will be quite expensive. Therefore, the time must be scaled. In order to scale the time correctly, frequency analysis can be performed first and the analysis time can be determined longer than the period corresponding to the first natural frequency. For three analysis methods mentioned within this study, validation studies were carried out with the examples in the literature. As a result of each type of analysis giving consistent results, the effect of parameters on static buckling load was examined, while linear eigenvalue analysis method was used because it was also sufficient for cheaper analysis method and comparison studies. While displacement-controlled analyses were carried out in the static buckling analyses mentioned, load-controlled analyses were performed in the analyses for the determination of dynamic buckling force. As a result of these analyses, they were evaluated according to different dynamic buckling criteria. There are some of the dynamic buckling criteria; Volmir criterion, Budiansky-Roth criterion, Hoff-Bruce criterion, etc. When Budiansky-Roth criterion is used, the first estimated buckling load is applied to the structure and displacement - time graph is drawn. If a major change in displacement is observed, it can be assumed that the structure is dynamically buckled. For Hoff-Bruce criterion, the speed - displacement graph should be drawn. If this graph is not focused in a single area and is drawn in a scattered way, it is considered that the structure has moved to the unstable area. As in static buckling analyses, dynamic buckling analyses were primarily validated with a sample study in the literature. After the analysis methods, the numerical studies were carried out on the effect of some parameters on the buckling load. First, the effect of the stacking sequence of composite layers on the buckling load was examined. In this context, a comprehensive study was carried out, both from which layer has the greatest effect of changing the angle and which angle has the highest buckling load. In addition, the some angle combinations are obtained in accordance with the angle stacking rules found in the literature. For those stacking sequences, buckling forces are calculated with both finite element analyses and analytically. In addition, comparisons were made with different materials. Here, the buckling load is calculated both for cylinders with different masses of the same thickness and for cylinders with different thicknesses with the same mass. Here, the highest force value for cylinders with the same mass is obtained for a uniform composite. In addition, although the highest buckling force was obtained for steel material in the analysis of cylinders of the same thickness, when we look at the ratio of buckling load to mass, the highest value was obtained for composite material. In addition, the ratio of length to diameter and the effect of thickness were also examined. Here, as the length to diameter ratio increases, the buckling load decreases. As the thickness increases, the buckling load increases with the square of the thickness. In addition to the effect of the length to diameter ratio and the effect of thickness, the loading time and the shape of the loading profile are also known in dynamic buckling analysis. In addition, the critical buckling force is affected by imperfections in the structure, which usually occur during the production of the structure. How sensitive the structures are to the imperfection may vary depending on the different parameters. The imperfection can be divided into three different groups as geometric, material and loading. Cylinders under axial load are particularly affected by geometric imperfection. The geometric imperfection can be defined as how far the structure is from a perfect cylindrical structure. It is possible to determine the specified amount of deviation by different measurement methods. Although it is not possible to measure the amount of imperfection for all structures, an idea can be gained about how much imperfection is expected from the studies found in the literature. Both the change in the buckling load on the measured cylinders and the imperfection effect of the buckling load can be measured by adding the measured amount of imperfection to the buckling load calculations. In cases where the amount of imperfection cannot be measured, the finite element can be included in the analysis model as an eigenvector imperfection obtained from linear buckling analysis and the critical buckling load can be calculated for the imperfect structure using nonlinear analysis methods. In this study, studies were carried out on how imperfection sensitivity changes under both static and dynamic loading with different parameters. These parameters are the the length-to-diameter ratio, the effect of the stacking sequence of the composite layers and the added imperfection shape. The most important result obtained in the study on imperfection sensitivity is that the effect of the imperfection on the buckling load is quite high. Even geometric imperfection equal to thickness can cause the buckling load to drop by up to half.